+ LIPO power packs
3s Entropy Race Pack 120C 6800mAh
These pointers are 'common sense' for lipo use
→New Entropy Lithium Polymer batteries need two charge & medium use cycles before hard use.
That said, this 'first use' policy should be applied to all high discharge Lipo packs.
→ Fully balance charge your new pack(s) at <5Amps, run your craft at <80% throttle for 1 minute, return, rest the pack, recharge and repeat. This 'proves / cures / sets / makes-ready ' the LiPo substrate for hard use.
→ Charge rate of 5C with Entropy is possible after above procedure is completed
The following applies at all times .....
→ Let packs rest 30+ minutes between use/charge cycles.
→ Do not charge packs when >40'c (thermal over run may occur )
→ Do not charge packs when <15'c (low temp will not permit full charge into substrate )
→ Do not charge swollen or punctured packs
→ Do not charge wet packs
→ Always balance charge +/- 0.01v/cell
→ If cell voltages are large differences, check the balance plug for damage / corrosion.. 99% that’s the flaw.
→ NEVER charge unattended .. always remain within sight of charging lipos .. fires have been caused by faulty chargers/abused lipos when on charge.
→ Optimal temp of packs before use is 25→35'c
→ Storage: balance to 3.85Vcell ... keep in a cool, dry & safe place away from flammables, animals and wide variations in temp. Optimal temp is 20’c
→Discharge below 3.0V will damage the cells.
ENTROPY come with Limited Warranty
DOA(unused): 14 days .. Manufacture faults: 3 months
Warranty available to original purchaser only.
Covers manufacturer defect / assembly / cell failure only..
Misuse, abuse or user error are not covered…
The polymer will display a pigment change when overheated .. beyond 55’c is considered thermal overload and pigment coloration changes to show this abuse.
DO NOT POST DAMAGED PACKS !
Photographic support for any claim must be submitted to aid consideration.
..
Disposal of lipo batteries .. submerge in salted water for 48 hours .. then remove any plugs and dispose at a recycling facility for batteries. Lithium is a finite resource .. recycling is smart !
Entropy. Efficiency in equilibrium with thermal stability.
AMPBA race legal at 478grams. 160x30x45mm
road freight only
Photos to come
4s Entropy Race Pack 120C 6800mAh
These pointers are 'common sense' for lipo use
→New Entropy Lithium Polymer batteries need two charge & medium use cycles before hard use.
That said, this 'first use' policy should be applied to all high discharge Lipo packs.
→ Fully balance charge your new pack(s) at <5Amps, run your craft at <80% throttle for 1 minute, return, rest the pack, recharge and repeat. This 'proves / cures / sets / makes-ready ' the LiPo substrate for hard use.
→ Charge rate of 5C with Entropy is possible after above procedure is completed
The following applies at all times .....
→ Let packs rest 30+ minutes between use/charge cycles.
→ Do not charge packs when >40'c (thermal over run may occur )
→ Do not charge packs when <15'c (low temp will not permit full charge into substrate )
→ Do not charge swollen or punctured packs
→ Do not charge wet packs
→ Always balance charge +/- 0.01v/cell
→ If cell voltages are large differences, check the balance plug for damage / corrosion.. 99% that’s the flaw.
→ NEVER charge unattended .. always remain within sight of charging lipos .. fires have been caused by faulty chargers/abused lipos when on charge.
→ Optimal temp of packs before use is 25→35'c
→ Storage: balance to 3.85Vcell ... keep in a cool, dry & safe place away from flammables, animals and wide variations in temp. Optimal temp is 20’c
→Discharge below 3.0V will damage the cells.
ENTROPY come with Limited Warranty
DOA(unused): 14 days .. Manufacture faults: 3 months
Warranty available to original purchaser only.
Covers manufacturer defect / assembly / cell failure only..
Misuse, abuse or user error are not covered…
The polymer will display a pigment change when overheated .. beyond 55’c is considered thermal overload and pigment coloration changes to show this abuse.
DO NOT POST DAMAGED PACKS !
Photographic support for any claim must be submitted to aid consideration.
..
Disposal of lipo batteries .. submerge in salted water for 48 hours .. then remove any plugs and dispose at a recycling facility for batteries. Lithium is a finite resource .. recycling is smart !
Entropy. Efficiency in equilibrium with thermal stability.
AMPBA race legal at 617grams. 160x40x45mm
road freight only
photos to come
6s Entropy race pack 120C 6800mAh
These directions are 'common sense' for lipo use
→New Entropy Lithium Polymer batteries need two charge & medium use cycles before hard use.
That said, this 'first use' policy should be applied to all high discharge Lipo packs.
→ Fully balance charge your new pack(s) at <5Amps, run your craft at <80% throttle for 1 minute, return, rest the pack, recharge and repeat. This 'proves / cures / sets / makes-ready ' the LiPo substrate for hard use.
→ Charge rate of 5C with Entropy is possible after above procedure is completed
The following applies at all times .....
→ Let packs rest 30+ minutes between use/charge cycles.
→ Do not charge packs when >40'c (thermal over run may occur )
→ Do not charge packs when <15'c (low temp will not permit full charge into substrate )
→ Do not charge swollen or punctured packs
→ Do not charge wet packs
→ Always balance charge +/- 0.01v/cell
→ If cell voltages are large differences, check the balance plug for damage / corrosion.. 99% that’s the flaw.
→ NEVER charge unattended .. always remain within sight of charging lipos .. fires have been caused by faulty chargers/abused lipos when on charge.
→ Optimal temp of packs before use is 25→35'c
→ Storage: balance to 3.85Vcell ... keep in a cool, dry & safe place away from flammables, animals and wide variations in temp. Optimal temp is 20’c
→Discharge below 3.0V will damage the cells.
ENTROPY come with Limited Warranty
DOA(unused): 14 days .. Manufacture faults: 3 months
Warranty available to original purchaser only.
Covers manufacturer defect / assembly / cell failure only..
Misuse, abuse or user error are not covered…
The polymer will display a pigment change when overheated .. beyond 55’c is considered thermal overload and pigment coloration changes to show this abuse.
DO NOT POST DAMAGED PACKS !
Photographic support for any claim must be submitted to aid consideration.
..
Disposal of lipo batteries .. submerge in salted water for 48 hours .. then remove any plugs and dispose at a recycling facility for batteries. Lithium is a finite resource .. recycling is smart !
Entropy. Efficiency in equilibrium with thermal stability.
AMPBA race legal at 914grams. 160x60x45mm
road freight only
Photo to come
infrared temperature reader
-50c -->> 400c infrared temperature gauge
requires 2x AAA batteries ( not supplied)Point and press smlicity
Enables you to safely acquire temperatures of batteries, motors, esc, or whatever you point the red dot onto !
ASA musthave tool for setups
- 1